Description

  • High performance
  • Built-in flow cell to reduce reagent consumption
  • Temperature control of the flow cell 37°C
  • Open system for all methods and reagents
  • Large LCD display
  • Built-in printer
  • Full-fledged kinetics with the construction of a graph of the reaction on the LCD display
  • Automatic filter wheel
  • Single or multi-point calibration
  • Non-volatile memory for 500 patients
  • Saving calibrations
  • External thermostat for 18 test tubes (option)
  • Alphanumeric keypad (option)

    Specifications

     

    Photometer type photometer with filter wheel
    Optical system configuration – single beam with continuously rotating filter wheel
    – monochromatic or bichromatic measurement 8 filter positions
    Methods of calculation and measurement Absorbance, Standard Mode, Differential samples blank, Factor Mode, Multi Standard Mode (up to 7 standards), Multi-point % Abs (Multi Standard) % Abs) (up to 7 standards), kinetics (Kinetic Mode) (sequentially or in groups (Batch)) by standard (Standard) or factor (Factor), fixed time (Fixed Time Kinetic) by standard (Standard) or factor (Factor )
    Channels 120 open
    Light source halogen lamp with tungsten filament, 10W
    Filter type 4-cavitational interference with ion sputtering
    Wavelength Accuracy + 3 nm
    Filters (wavelengths) – 340, 405, 505, 545, 580, 630 nm (standard)
    – automatic filter wheel
    Cuvettes 1 cm square cell, 12 mm round tube, flow cell
    flow cell 316 stainless steel, borosilicate window glass,
    cylindrical, diameter 2.3 length 5 + 0.05 mm
    Minimum volume 250 μl
    Aspiration/Purge vacuum pump, 18 cm Hg
    Valve silicone, pinch type
    Cuvette holder compartment with temperature control 37°С
    Detector gallium arsenide phosphide photodiode
    Display 240 x 126 graphic LCD with backlight
    Absorption – -0.5 to 3.5 (flow cell)
    – -0.5 to 2.5 (tube or 1 cm cuvette)
    Concentration maximum 999,999
    Zero compensation automatic
    Interfaces – LPT (Centronics, D-sub 25p)
    – RS-232 (D-sub 9p)
    Data input 1. built-in 20 key keyboard; 2. external PS2 101 key keyboard (connector on the rear panel of the device) – not included
    Warm-up time – 90 s for photometer
    – 15 min for thermostat
    Electronics – microprocessor Z180 18 MHz
    – 128 KB EEPROM memory
    – 32 KB non-volatile memory (NVRAM)
    Printer thermal printer, paper 110 mm
    Power supply 90-260 V (auto-tuning), 50/60 Hz, 60 W, CAT II fuses: 2.5 A / 250 V, 2.0 A / 250 V
    Temperature, humidity 15 – 35°C, humidity less than 85%
    Dimensions, weight 40 x 37 x 14 (30) cm with closed lid, 6.4 kg

     

    Tests in progress

  • Enzymes: AST, ALT, gamma-GT, LDH, alpha-amylase, creatine kinase, creatine kinase MB-fraction, lipase, alkaline phosphatase, acid phosphatase, cholinesterase, HBDG, LAP, PGI
  • Substrates: uric acid, albumin, direct and total bilirubin, creatinine, glucose, hemoglobin, lactate, total protein, urinary microalbumin, urea, urinary and CSF protein, fructosamine
  • Lipids: cholesterol, HDL cholesterol, LDL cholesterol, triglycerides, phospholipids, total lipids
  • Electrolytes: potassium, sodium, calcium, chlorides, iron, TIBC, copper, magnesium, phosphorus, zinc
    Serum protein immunoturbidimetry: apolipoproteins A1, B, CII, CIII, E 1-acid glycoprotein, antithrombin III, ceruloplasmin, C-1-Esterase, complement C 3, complement C 4, haptoglobin, IgG, IgA, IgM, kappa (Ig light chains), lambda (Ig light chains), prealbumin, transferrin
  • Latex immunoturbidimetry of serum proteins: C-reactive protein (CRP), rheumatoid factor (RF), antistreptolysin O (ASLO), lipoprotein (a) LP(a), beta-2-microglobulin, ferritin, immunoglobulin E (IgE), myoglobin, microalbumin, alpha-fetoprotein, glycated hemoglobin